INSTALLATION GUIDE FOR

Defender 8™ PIGEON SPIKES PLASTIC

Defender 8™ plastic spikes Defender 8™ plastic spikes Defender 8™ plastic spikes

Defender 8™ Pigeon Spikes - PlasticThe Defender 8™ Pigeon Spikes Plastic is made from UV stabilised polycarbonate which means that it will not go brittle even if positioned in direct sunlight.







Defender 8™ Pigeon Spikes - PlasticThe Defender 8™ Pigeon Spikes Plastic should be used to protect ledges that have a depth of up to 8 inches (200mm). Each strip has an overall length of just just over 13” (337mm).







Defender 8™ Pigeon Spikes - Plastic1. All areas should be prepared ensuring they are clean, dry and free from bird droppings. It is important to look up; it may be that the source of the mess is actually from ledges or pipes higher up on the building. If this is the case you will need to spike these as well. If this is not done, then droppings, twigs etc. may fall down onto the pigeon spikes below rendering them less effective.

Defender 8™ Pigeon Spikes - Plastic2. Squeeze pigeon spike fixing silicone generously onto the base of the spike, about (10mm) the size of your finger. Thicker if the ledge is uneven.







Defender 8™ Pigeon Spikes - Plastic3. Stick the first row of pigeon spikes towards the front of the ledge, so that the spikes fully protect the leading edge. Press down firmly so the glue oozes out through the little holes. If the gap behind the 1st row is greater than 2 inches (5cm) pigeons may get in behind. It is therefore necessary to install another row of spikes into this space to block it. For very wide ledges 3 or more rows of pigeon spikes may be required remembering to leave no more than 2 inches (5cm) between rows.

Defender 8™ Pigeon Spikes - Plastic4. Every effort should be made to spike all possible landing sites that are 2 inches (5cm) or greater. Snap spikes into pieces to finish off rows or spike small areas. Spikes can be easily snapped using your fingers.





Defender 8™ Pigeon Spikes - Plastic5. Very important: Pigeon spikes will stop pigeons from sitting on a ledge; however if there is a hole in the eaves or a cavity in the exterior wall behind the spikes, pigeons will invariably force their way past the spikes in an effort to get into that hole. Simply putting a spike in front of a hole will not stop the pigeon. Every effort should be made to block the access to this hole or space. You might be able to seal that hole with wire mesh or expanding foam.

Please note: before blocking the hole you should ensure that pigeons have not become trapped in the recess. If you do discover any pigeon squabs or dependent birds please contact your local wildlife rehabilitator which can be found here.

Defender 8™ Pigeon Spikes - Plastic6. Always make sure that the base of the bird spikes are fixed directly onto the top of any parts of the ledge that may be raised slightly higher than the rest of the ledge. If this is not done then pigeons will overcome any spikes on lower parts by standing on the raised section. Spike the highest part of the ledge first then move on to spike the lower sections afterwards.

Defender 8™ Pigeon Spikes - Plastic7. Window cleaners, contractors on ladders, scaffolders, painters etc. have a habit of damaging pigeon spikes. Warn them to be careful whilst working. A slightly damaged spike is likely to provide an ideal roosting or nesting spot for a pigeon. Any damaged spikes should be replaced before the pigeons move in.

Take Health & Safety Precautions8. Before starting the job, assess the work to make sure that you can do it safely and without hurting yourself or others. If you have any doubts at all then please contact us or return the spikes for a full refund – no questions asked. Wear suitable protective clothing, dust mask, gloves, overalls etc.

Buy this product now!

Back to top